Receiving Faxes

This section describes the methods for receiving faxes and how to set up the machine to receive faxes. You need to complete some procedures for using fax functions before specifying the receiving settings. Configuring Initial Settings for Fax Functions


Some settings may not be displayed depending on your country or region.

Methods for Receiving Faxes

The machine provides the following receiving methods. Select the method that best suits your needs and then set it up by following the procedures in Setting Up the Machine to Receive Faxes.

<Auto>	Dedicated to receiving faxes The machine receives faxes automatically. Even if someone makes a call to you, you cannot talk to the caller.
<Fax/Tel (Auto Switch)>	When the call is a fax The machine receives the fax automatically. When the call is a telephone call An incoming call rings. Pick up the handset to answer the call. You need to connect your telephone to the machine beforehand.
<Manual>	When the call is a fax An incoming call rings. Pick up the handset. If you hear a beep, select <Fax> <Start Receiving> to receive faxes. When the call is a telephone call An incoming call rings. Pick up the handset and start your conversation. You need to connect your telephone/handset to the machine beforehand. You can set the machine to automatically receive faxes when an incoming call rings within a specified timeframe. <Switch to Auto RX>
<Answering Machine>	When the call is a fax After an incoming call rings, the machine receives the fax automatically. When the call is a telephone call The answering machine activates, enabling the caller to leave a message. If you pick up the handset before the answering machine starts recording a message, you can talk with the caller. You need to connect your answering machine to the machine beforehand. Set the answering machine to answer after a few rings. We recommend that you add approximately 4 seconds of silence at the beginning of the message or set the maximum recording time to 20 seconds.
<DRPD: Select Fax>	If you have subscribed to a Distinctive Ring Pattern Detection (DRPD) service provided by your telephone company, this receiving mode is available. This service assigns two or more telephone numbers with distinctive ring patterns to a single telephone line. You can use one of these numbers for faxes and one for telephone calls. When the machine receives a call, it automatically recognizes the ring pattern and your telephone rings differently depending on whether the call is a fax or telephone call. If the ring pattern is for a fax, the machine automatically receives the fax. For more information about this service, contact your telephone company. You need to connect your telephone to the machine beforehand.
<Net Switch>	The machine distinguishes between fax and telephone calls. This mode is only available for certain countries and requires a subscription to a network switch service. You need to connect your telephone or the handset to the machine beforehand. Telstra FaxStream. Duet (Only for Australia) In Australia, Telstra offers the FaxStream. Duet capability. If you subscribe to this service, your line is assigned two numbers: one for fax and one for phone. When the fax number is called, the network sends a specific ringing tone which your machine recognizes and automatically handles as a fax call. If the phone number is called, a different ringing tone is sent out from the network so that the call is handled as a voice call. This means that there is no switching delay at the caller's end. Contact Telstra for connection information. Triple ring (short-short-short) for fax receiving. Three short rings, at regular intervals. Any ring except triple ring (depending on your switchboard) for telephone conversation. You need to subscribe to the FaxStream service beforehand. Telecom FaxAbility (Only for New Zealand) In New Zealand, Telecom N.Z. offers the FaxAbility capability. This service allows you to assign two numbers to your line: one for fax and one for telephone. When the fax number is called, the network sends a specific ring tone which your machine recognizes and automatically handles as a fax call. If the telephone number is called, a different ring tone is sent out from the network so that the call is handled as a voice call. This means that there is no switching delay at the caller's end. Contact Telecom for connection information. You need to subscribe to the FaxAbilty service beforehand.


Depending on the type of telephone connected to it, the machine may not be able to send or receive faxes properly. If you are connecting an external telephone with fax functions, set the telephone to not receive faxes automatically. If you pick up the telephone handset and hear a beep, the call is a fax. You can receive the fax just by using the telephone to enter a specific ID number. Using a Telephone to Receive Faxes (Remote Reception)

Depending on the type of telephone connected to it, the machine may not be able to send or receive faxes properly.

If you are connecting an external telephone with fax functions, set the telephone to not receive faxes automatically.

If you pick up the telephone handset and hear a beep, the call is a fax. You can receive the fax just by using the telephone to enter a specific ID number. Using a Telephone to Receive Faxes (Remote Reception)

Setting Up the Machine to Receive Faxes

Select <Fax> in the Home screen. Home Screen

When the login screen appears, enter your user name and password and set up the authentication server. Logging in to Authorized Send

Select <RX Mode> in the <TX/RX Settings> tab of the Fax Basic Features screen. Fax Basic Features Screen

Select the receiving method.

When selecting <Fax/Tel (Auto Switch)>

Specify the following three settings as necessary. When the setting is complete, select <Apply>.

<Ring Start Time>
Enables you to specify the duration during which the machine determines whether an incoming call is a fax or a telephone call.

<Incoming Ring Time>
Enables you to specify the duration during which an incoming call rings for a telephone call.

<Action After Ring>
Enables you to specify how the machine operates if you do not pick up the handset while an incoming call is ringing. Select <End> to disconnect the call or <Receive> to receive an incoming fax.

When selecting <DRPD: Select Fax>

Select the ring pattern that your telephone company assigned to your fax number.


If you want to print received documents on both sides of paper: <Print on Both Sides> If you want to print information, such as reception date and time, at the bottom of received documents: <Print RX Page Footer>

Using a Telephone to Receive Faxes (Remote Reception)

When you pick up the telephone and get a fax signal, you do not need to go to the machine to receive the fax. Just enter a specific ID number with the telephone, and you can start receiving the fax.


When the telephone is not directly connected with the machine, the remote reception function is not available.

When an incoming call rings, pick up the telephone handset.

If you hear a beep, enter the ID number for Remote Reception with the telephone.

For more information about setting the ID number, see <Remote RX>.

Hang up the handset.

Checking Status and Log for Sent and Received Documents

Various Receiving Methods