Loading Roll Paper in the Roll Unit
Follow these steps to load roll paper in the roll unit.
When selecting Enable in Roll paper auto feed, the roll paper is fed automatically by simply loading it.
Important
-
Always load rolls when the printer is on. If the printer is off when you load a roll, the paper may not be advanced correctly when you turn the printer on.
-
Before loading a roll, confirm whether the inside of the top cover or the output guide is soiled. If these areas are dirty, we recommend cleaning them in advance.
-
If using the roll unit as the feed device, depending on the basket position, the ejected roll paper's cut end enters the roll unit and may cause a paper jam or affect the print quality when set to "Borderless Printing" or "Trim Edge First" when loading the paper. In this case, change the basket position, and then print.
-
If Paper retention settings is set to Release, the roll paper is not fed automatically.
-
For details on the paper that can feed roll paper automatically, see "Paper Information List."
Note
-
When roll paper cannot be fed automatically, see "Roll Paper Is not Switched Automatically."
-
Select the paper setting display area on Home screen.
-
Select the Roll paper 2 area.
-
Select Load paper or Replace paper.
Note- If any paper has been advanced that will not be used, a message is shown requesting you to remove it. After following the instructions on the screen to remove the paper, go to the next step.
-
Change Roll Holder Lock switch on roll unit to release position.
-
Hold flanges (A) so that holder stopper is on left, align roll holder shaft with roll holder slot left and right guide grooves (B), and load.
Caution-
Do not force the roll holder into the printer with the right and left ends reversed. This may damage the printer and roll holder.
-
Do not release the flanges until the holder is loaded in the roll holder slot.
-
Be careful not to pinch your fingers between the Roll Holder shaft and the guide grooves (B) when loading the roll paper.
Important-
If the leading edge of the roll paper is secured with tape or a paper band so that it will not unravel, remove the tape or paper band before loading the roll paper into the roll holder slot.
If you load the paper into the roll holder slot with the leading edge secured, only part of the roll paper is fed to the paper feed slot, resulting in damage to the roll paper.
-
If the leading edge of the roll paper is cut crooked or folded, it may not be fed correctly. Cut the leading edge of the roll paper with scissors or the like and straighten it.
-
Load the roll paper so that it is not loaded in the opposite direction.
-
Make sure there is no slack in the roll paper, and then load it.
-
Depending on the surrounding environment, the leading edge of roll paper is stuck because of static electricity or humidity so that the roll paper may not be able to be fed correctly. In this case, set Roll paper auto feed to Disable, and then feed the roll paper.
-
If the roll paper is decentered, it may not be able to be fed correctly. In this case, set Roll paper auto feed to Disable, and then feed the roll paper.
-
When Roll paper auto feed is Enable and if you attach the roll holder without the roll paper loaded on the roll holder, Preparing to feed the paper... appears on the operation panel. In this case, press the Stop button on the operation panel to cancel feeding.
Note-
For the procedure for attaching the roll paper to the Roll Holder, see "Loading Rolls on the Roll Holder."
-
-
Change Roll Holder Lock switch on roll unit to locked position.
Important-
If you do not change Roll Holder Lock switch to locked position, the roll paper cannot be fed automatically.
-
-
Change feed flap switch on top of roll unit to feed icon position on the left.
-
When selecting Enable in Roll paper auto feed.
The roll paper is fed.
-
When selecting Disable in Roll paper auto feed.
Pull out roll paper evenly, insert leading edge between roll paper and arrows (A) directly beneath it, and feed roll paper until you hear a sound.
Select Start feeding, and then the roll paper is fed.
Important-
If the roll paper has become unwound, remove the slack before loading the roll paper.
-
When feeding the leading edge of the roll paper, make sure the entire width of the roll paper is separating and feeding from the roll. If the roll paper is fed with some of the roll paper still stuck to the roll, the roll paper will be damaged.
-
Be careful not to soil the printing surface of roll paper as you insert it in the slot. This may affect the printing quality. We recommend wearing clean cloth gloves when handling rolls to protect the printing surface.
-
If the paper is wrinkled or warped, straighten it out before loading it.
-
Load the roll so that there is no gap between the right edge of the paper and the Roll Holder.
-
Depending on the paper, the roll paper may be scratched when being fed and not feed well. In this case, you must feed the paper manually after setting Paper retention settings to Release on the touch screen. Lift the release lever, advance the roll paper until its leading edge appears on platen, lower the release lever, and then proceed to the next step. However, if Paper retention settings is set to Release, automatic switching of the upper and lower rolls is not possible.
-
-
After paper feeding has started, do the following operations based on the Manage remaining roll amount setting and the barcode printed on the roll paper
-
When selecting Disable or Auto estimate in Manage remaining roll amount.
-
When selecting Manual or Auto with confirmation in Media type selection method.
A menu for selecting the media type appears on the touch screen. Operate the touch screen and select the media type to be used.
-
When selecting Auto detect in Media type selection method.
You'll see candidate for the media type you've estimated to the touch screen. After 5 seconds, the paper type of the first item is selected. If you choose a different candidate, you can use the touch screen to select the type of paper you want.
-
When selecting Use current media type in Media type selection method.
A menu for selecting the media type appears on the touch screen. After 5 seconds, the media type will be selected with the fixed media kind.
-
-
When selecting Barcodes in Manage remaining roll amount and if the barcode is printed.
The type and amount of paper left is automatically detected based on the barcode printed on the roll. There is no need to specify the type and length of the paper.
-
When selecting Barcodes in Manage remaining roll amount and if the barcode is not printed.
-
When selecting Manual in Media type selection method.
A menu for selection of the media type and length is shown on the touch screen.Operate the touch screen, select the media type to be used, and enter its length.
-
When selecting Auto with confirmation in Media type selection method.
A menu for selecting the estimated media type candidates and the paper length. Interact with the touch screen, select the media type you want to use, and enter the length.
-
When selecting Auto detect in Media type selection method.
A menu for selecting the estimated media type candidates and the paper length.After 5 seconds, the paper type of the first item is selected. If you choose a different candidate, you can use the touch screen to select the type of paper you want.
-
When selecting Use current media type in Media type selection method.
A menu for selecting the media type and the paper length appears on the touch screen. After 5 seconds, the media type will be selected with the fixed paper kind.
-
Important-
If the leading edge of the roll paper is folded or stained, cut the leading edge of the roll paper.
Note-
If you have selected Auto with confirmation or Auto detect in the Media type selection method and you are using the barcode to manage the remaining roll paper, the barcode is read first. If it fails to read the barcode, it will detect the media type from the estimated result and display the candidate.
-
For details on media types that you can select, see "Paper Information List."
-
The width of the roll paper is automatically detected by the printer when the paper is loaded.
When using roll paper with a user-defined size width, the detected width length and the set width length must exactly match, so even if the correct roll paper is loaded, detection may fail.
In this case, you can improve it by setting the roll paper width you want to use in Add priority roll paper width.
-
