FAX settings
- FAX user settings
- Advanced FAX settings
- Auto print settings
- Auto save setting
- Security control
- Easy setup
Note
-
Before changing the settings, you can confirm the current settings by printing USER'S DATA LIST.
FAX user settings
-
User information settings
Registers your name and fax/telephone number printed on sent faxes.
-
Telephone line type (Country or region of purchase other than China)
Selects the telephone line type setting for the printer.
Note- This setting may not be available depending on the country or region of purchase.
-
Telephone line auto selection (China only)
If you select ON, the telephone line type is selected automatically.
If you select OFF, you can select the telephone line type manually.
Advanced FAX settings
-
Error reduction setting (VoIP)
If you select Reduce, it may be possible to reduce the incidence of communication errors when connecting to internet line such as IP phone.
Note- When Reduce is selected, V.34 (Super G3) can not be used. Communication time generally becomes longer than when communicating with V.34 (super G3).
- This setting has priority even if you select 33600 bps for TX start speed or RX start speed.
-
Auto redial
Enables/disables automatic redialing.
If you select ON, you can specify the maximum number of redial attempts and the length of time the printer waits between redial attempts.
-
Dial tone detect
Avoids mistransmission when reception and transmission occur at the same time.
If you select ON, the printer transmits the fax after confirming the dial tone.
Note- This setting may not be available depending on the country or region of purchase.
-
Pause time settings
Sets the length of pause time for each when you enter "P" (pause).
-
TTI position
Selects the position of the sender information (outside or inside the image area).
-
Remote RX
Enables/disables remote reception.
If you select ON, you can specify the remote reception ID.
-
Color transmission
When faxing color documents using the ADF, selects whether to convert them into black & white data if the recipient's fax device does not support color faxing.
If you select Disconnect, the printer does not send color documents when the recipient's fax device does not support color faxing.
-
RX image reduction
Enables/disables automatic reduction of incoming faxes so that they fit in the selected paper.
If you select ON, you can select the image reduction direction.
-
Adv. communication settings
-
ECM TX
Selects whether to send faxes in Error Correction Mode (ECM).
-
ECM RX
Selects whether to receive faxes in Error Correction Mode (ECM).
-
TX start speed
Selects the fax transmission speed.
The fax transmission start speed will be faster as the value is bigger.
When the telephone line condition or connection is poor, selecting a lower transmission start speed may solve transmission problems.
-
RX start speed
Selects the fax reception speed.
The fax reception start speed will be faster as the value is bigger.
When the telephone line condition or connection is poor, selecting a lower reception start speed may solve reception problems.
-
Auto print settings
-
Received documents
Selects whether to print the received fax automatically when receiving a fax.
If you select Do not print, the received fax is stored in the printer's memory.
For details on the received fax stored in the printer's memory:
-
Activity report
Selects whether to print ACTIVITY REPORT automatically.
If you select Print, the printer prints ACTIVITY REPORT for the 20 histories of sent and received faxes automatically.
For details on the procedure to print ACTIVITY REPORT manually:
-
TX report
Selects whether to print TX REPORT/ERROR TX REPORT automatically after sending a fax.
If you print the report, select Print error only or Print for each TX.
If you select Print error only or Print for each TX, you can specify the print setting that the first page of the fax is printed along with the report.
-
RX report
Selects whether to print RX REPORT automatically after receiving a fax.
If you print RX REPORT, select Print error only or Print for each RX.
-
Print when out of ink
Sets whether to continue printing the received fax without storing it in the printer's memory when the ink has run out.
However, part or all of the fax may not be printed since the ink has run out.
Auto save setting
Selects whether to save the received fax on the memory card automatically after receiving a fax.
Security control
-
FAX number re-entry
If you select ON, you can set the printer to send faxes after entering the number twice. By using this setting, you can avoid the mistransmission of faxes.
-
Check RX FAX information
If you select ON, the printer checks whether the recipient's fax device information matches the dialed number. If it matches the number, the printer starts to send faxes.
-
Hook key setting
If you select Enable, you can use the on hook dial function.
-
FAX reception reject
If you select ON, the printer rejects the reception of faxes with no sender information or faxes from specific senders.
-
Caller rejection
If you subscribe to the Caller ID service, the printer detects the sender's Caller ID. If the sender's ID matches the condition specified in this setting, the printer rejects the phone call or fax reception from the sender.
If you select Yes on the subscribing confirmation screen, you can specify the settings of rejection.
Note- This setting may not be supported depending on the country or region of purchase. Contact your telephone company to confirm whether it provides this service.
Easy setup
The printer must be set up depending on your telephone line and use of the faxing function. Follow the procedure according to the instructions on the touch screen.
Note
-
You can specify the setup setting individually or the advanced setting.
For details on how to specify the setting:
