Canon : Inkjet Manuals : TR7000 series : LAN settings

Wi-Fi

Show setting info

The network settings information of the printer appears when it is connected by Wi-Fi. (Some setting items are not displayed depending on the printer settings.)

Items	Setting
Connection	Enabled (connected)/Enabled (disconnected)/Disable
Network name (SSID)	XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX (up to 32 characters)
Wi-Fi security	Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)
Signal strength (%)	XXX
IPv4 address	XXX. XXX. XXX. XXX (12 characters)
IPv4 subnet mask	XXX. XXX. XXX. XXX (12 characters)
IPv4 default gateway	XXX. XXX. XXX. XXX (12 characters)
IPv6 link-local address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
MAC address (Wi-Fi)	XXX. XXX. XXX. XXX (12 characters)
Printer name	XXXXXXXXXXXXXXX (up to 15 characters)
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters)

("XX" represents alphanumeric characters.)

Advanced mode

Enables/disables Wi-Fi.
Wi-Fi setup

Selects the setup method for Wi-Fi connection.
- Easy wireless connect
  
  Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure.
- Manual connect
  
  Select when you perform settings for Wi-Fi manually using the operation panel of the printer.
- WPS (Push button method)
  
  Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
- Other connection types
  - Manual connect (adv.)
    
    Select when you perform settings for Wi-Fi manually. You can specify multiple WEP keys.
  - WPS (PIN code method)
    
    Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
Advanced

For details on each setting item:
- Advanced

Wireless Direct

Show setting info

The network settings information of the printer appears when it is connected by the wireless direct. (Some setting items are not displayed depending on the printer settings.)

Note

Select Show setting info to display a screen, allowing you to show or hide the password.

Items	Setting
Connection	Enable/Disable
Network name(SSID)	DIRECT-XXXXXXXXX XXXXXXXXXXXXXXXX (up to 32 characters)
Password	XXXXXXXXXX (10 characters)
Wi-Fi security	WPA2-PSK(AES)
No. of devices connected now	XX/XX
IPv4 address	XXX. XXX. XXX. XXX (12 characters)
IPv4 subnet mask	XXX. XXX. XXX. XXX (12 characters)
IPv4 default gateway	XXX. XXX. XXX. XXX (12 characters)
IPv6 link-local address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
MAC address (Wi-Fi)	XXX. XXX. XXX. XXX (12 characters)
Printer name	XXXXXXXXXXXXXXX (up to 15 characters)
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters)

("XX" represents alphanumeric characters.)

Connect to smartphone

Enables to connect the smartphone to the printer by reading the QR code displayed on the LCD with the smartphone, or also by manually obtaining the network name and password.
Advanced mode

Enables/disables Wireless Direct.
Change network name (SSID)

Changes the identifier (SSID/the printer's name displayed on a Wi-Fi Direct compatible device) for Wireless Direct.
Change password

Changes the password for Wireless Direct.
Connection request confirmation

Selecting ON displays the confirmation screen when a Wi-Fi Direct compatible device is connecting the printer.
Advanced

For details on each setting item:
- Advanced

Advanced

Set printer name

Specifies the printer name. You can use up to 15 characters for the name.

Note
- You cannot use the same printer name as that already used for other LAN connected devices.
- You cannot use a hyphen for the initial or last character of the printer name.
TCP/IP settings

Performs IPv4 or IPv6 setting.
WSD setting

Setting items when you use WSD (one of the network protocols supported in Windows).
- Enable/disable WSD
  
  Selects whether WSD is enabled or disabled.
  
  Note
  - When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows.
- Optimize inbound WSD
  
  Selecting Enable allows you to receive the WSD printing data faster.
- Timeout setting
  
  Specifies the timeout length.
Bonjour settings

Setting items when you use Bonjour.
- Enable/disable Bonjour
  
  Selecting Enable allows you to use Bonjour to perform the network settings.
- Service name
  
  Specifies the Bonjour service name. You can use up to 48 characters for the name.
  
  Note
  - You cannot use the same service name as that already used for other LAN connected devices.
LPR protocol setting

Enables/disables the LPR setting.
RAW protocol

Enables/disables RAW printing.
LLMNR

Enables/disables LLMNR (Link-Local Multicast Name Resolution). Selecting Enable allows the printer to detect printer's IP address from the printer name without a DNS server.
IPP settings

Selecting Enable allows you to print via the network with the IPP protocol.
PictBridge communication

Setting items for printing from a PictBridge (Wi-Fi) compliant device.
- Enable/disable communication
  
  Selecting Enable allows you to print from a PictBridge (Wi-Fi) compliant device.
- Timeout setting
  
  Specifies the timeout length.
IPsec settings

Selecting Enable allows you to specify the IPsec security.