Forwarding Scanned Data to the Computer Using the Operation Panel of the Machine

Before forwarding scanned data to the computer, confirm the following:

• MP Drivers are installed.

  If MP Drivers are not yet installed, install MP Drivers with the Setup CD-ROM or install them from our website.

• The machine is connected to a computer correctly.

  Make sure that the machine is connected to the computer correctly.

  Do not plug in or unplug the USB cable while the machine is in operation, or when the computer is in the sleep or standby mode.

  If you perform scanning via a network connection, make sure that all the required settings have been specified.

  Network Scan Settings

• The destination and the file name are specified in Canon IJ Scan Utility.

  You can specify the destination and the file name in Canon IJ Scan Utility. For details on settings of Canon IJ Scan Utility:

  Settings Dialog Box

Follow the procedure below to forward scanned data to the computer.

1. Make sure that the machine is turned on.

2. Press the SCAN button.

   If you forward the scanned data to a USB-connected or LAN connected computer for the first time, the Scan menu screen is displayed. Go to step 3.

   

   If you have forwarded the scanned data to a computer, the Scan standby screen is displayed.

   

   * The Scan standby screen for USB-connected computer

   If you change the destination or scan settings, press the Menu button, then go to step 3.

   Go to step 9 if you do not change the destination or scan settings.

3. Use the button to select Save to, then press the OK button.

4. Use the button to select PC, then press the OK button.

5. Use the button to select the computer to forward the scanned data, then press the OK button.

   If you forward the data to the USB-connected computer, select Local (USB).

   If you forward the data to the LAN-connected computer, select a name of the computer to forward the scanned data.

   Note

   • If you select Search again and press the OK button, the machine starts searching for the connected computers again.

   • When you forward the scanned data to the computer using WSD (one of the network protocols supported in Windows 8, Windows 7, and Windows Vista), select Active for WSD scan from dev. on WSD setting on Other settings in LAN settings under Device settings.

6. Make sure that Document type is selected, then press the OK button.

7. Use the button to select the document type, then press the OK button.

   Note

   • When you forward the scanned data to the computer searched using WSD, you cannot select the document type.

   • The * (asterisk) on the LCD indicates the current setting.

   Auto scan

   This item is available only when the machine is connected to the computer using a USB cable.

   The machine detects the type of the originals automatically and the image is forwarded in the optimized size, resolution and data format.

   Important

   • You can select Auto scan only when you forward the scanned data to the USB-connected computer.

   • Load originals properly according to their type; otherwise, some originals may not be scanned properly.

     For details on how to load the original:

     Loading Originals

   • The following items can be scanned:

     Photos, postcards, visiting cards, magazines, newspapers, documents, BD/DVD/CDs

   • The following items cannot be scanned properly.

     • A4 sized photos

     • Documents smaller than 5 inches x 7 inches (127 mm x 178 mm) such as a paperback with its backbone cut off

     • Originals on thin white paper

     • Long and narrow originals such as panoramic photographs

   • When you scan originals from the ADF, it may take longer to scan the first page.

   Document

   Scans the original on the platen glass or in the ADF applying the optimized settings for scanning a document.

   Photo

   Scans the original on the platen glass as a photo data applying the optimized settings for scanning a photo.

8. Specify the scan settings.

   Specify each scan setting in order.

   Note

   • For details on each setting item:

     Setting Items for Scanning Using the Operation Panel of the Machine

   • Go to step 9 when Auto scan is selected for Document type.

   1. Make sure that Scan size is selected, then press the OK button.

   2. Use the button to select the scan size, then press the OK button.

   3. Make sure that Data format is selected, then press the OK button.

   4. Use the button to select the data format, then press the OK button.

   5. Make sure that Scan resolution is selected, then press the OK button.

   6. Use the button to select the scan resolution, then press the OK button.

      The Scan standby screen is displayed after all the settings have been specified.

      

9. Load the original document on the platen glass or in the ADF.

10. Press the Color button for color scanning, or the Black button for black & white scanning.

    Note

    • When you forward the scanned data to the computer using WSD, press the Color button.

    • If the original is not loaded properly, a message is displayed on the LCD. Load the original on the platen glass or in the ADF according to the scan settings.

    • If you load the original in the ADF:

      The machine starts scanning and scanned data is forwarded to the computer.

    • If you load the original on the platen glass:

      • When you select JPEG or TIFF for Data format, the machine starts scanning and scanned data is forwarded to the computer.

      • When you select PDF or Compact PDF for Data format, the confirmation screen asking you if you continue scanning is displayed after scanning is complete.

        Selecting Yes and pressing the OK button allow you to scan the originals continuously. Load the next document on the platen glass and start scanning.

        By selecting No and pressing the OK button, scanning is complete and the data is forwarded to the computer in one PDF file.

    Scanned data is forwarded to the computer according to the settings specified in Canon IJ Scan Utility.

    Remove the original on the platen glass or from the document output slot after scanning is complete.

    Important

    • If the scanning result with Auto scan is not satisfactory, select Document or Photo according to the original in step 7, then specify the scan size or other setting items in step 8.