LAN settings

Important

This setting item is for the administrator.

Change LAN

Enables either wireless LAN or access point mode. You can also disable wireless LAN or access point mode.
Wireless LAN setup

Selects the setup method for wireless LAN connection.

Note
- You can also enter this setting menu by selecting WLAN on the HOME screen. In this case, enable wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the machine detects the access point, follow the on-screen instructions to set up wireless LAN. If an access point is not detected or if you select another setup method, select one of the setup methods below.
- Standard setup
  
  Select when you perform settings for wireless LAN manually using the operation panel of the machine.
- WPS (Push button method)
  
  Select when you perform settings for wireless LAN using an access point supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
- Other setup
  
  Advanced setup
  
  Select when you perform settings for wireless LAN manually. You can specify multiple WEP keys.
  
  WPS (PIN code method)
  
  Select when you perform settings for wireless LAN using an access point supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
  
  Cableless setup
  
  Select if you specify the settings of the access point information to the machine directly from a device (such as a smartphone) without operating the access point. Follow the on-screen instructions of the connecting device for the setup procedure.

Confirm LAN settings

The list of wireless LAN settings or the access point mode of this machine is displayed on the LCD. You can print the list from this setting menu.

WLAN setting list

The list of wireless LAN settings of this machine is displayed on the LCD.

The following setting items are displayed.

Items	Setting
Connection	Active/Inactive
SSID	XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
Communication mode	Infrastructure
Channel	XX
Wireless LAN security	Inactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-PSK(TKIP)/WPA2-PSK(AES)
IPv4 address	XXX. XXX. XXX. XXX
IPv4 subnet mask	XXX. XXX. XXX. XXX
IPv4 default gateway	XXX. XXX. XXX. XXX
IPv6 address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
IPv6 subnet prefix length	XXX
IPv6 default gateway	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
MAC address	XX:XX:XX:XX:XX:XX
IPsec settings	Enable (ESP)/Enable (ESP & AH)/Enable (AH)/Disable
Pre-shared key	XXXXXXXXXXXXXXXX
Printer name	XXXXXXXXXXXXXXX
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX

("XX" represents alphanumeric characters.)

AP mode setting list

The list of access point mode settings of this machine is displayed on the LCD.

The following setting items are displayed.

Items	Setting
Connection	Active/Inactive
SSID	XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX
Password	XXXXXXXXXX
Communication mode	Access point mode
Channel	3
Wireless LAN security	Inactive/WPA2-PSK(AES)
IPv4 address	XXX. XXX. XXX. XXX
IPv4 subnet mask	XXX. XXX. XXX. XXX
IPv4 default gateway	XXX. XXX. XXX. XXX
IPv6 address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
IPv6 subnet prefix length	XXX
IPv6 default gateway	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX
MAC address	XX:XX:XX:XX:XX:XX
IPsec settings	Disable
Pre-shared key	XXXXXXXXXXXXXXXX
Printer name	XXXXXXXXXXXXXXX
Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX

("XX" represents alphanumeric characters.)

Print LAN details

You can print out the network settings of the machine such as its IP address and SSID.

For more information on the machine's network setting is printed out:

Printing Out Network Setting Information

Important
- This printout contains valuable information about your computer. Handle it with care.

Other settings

Important
- You cannot select the items below when Disable LAN is selected for Change LAN.
- Set printer name
  
  Specifies the printer name. You can use up to 15 characters for the name.
  
  Note
  - You cannot use the same printer name as that already used for other LAN connected devices.
  - You cannot use a hyphen for the initial or last character of the printer name.
- TCP/IP settings
  
  Performs IPv4 or IPv6 setting.
- WSD setting
  
  Setting items when you use WSD (one of the network protocols supported in Windows 8.1, Windows 8, Windows 7, and Windows Vista).
  Enable/disable WSD
  
  Selects whether WSD is enabled or disabled.
  
  Note
  - When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows 8.1, Windows 8, Windows 7, and Windows Vista.
  WSD scan from this device
  
  Selecting Enable allows you to transfer the scanned data to the computer using WSD.
  
  Timeout setting
  
  Specifies the timeout length.
- Bonjour settings
  
  Setting items for LAN using Bonjour for Mac OS.
  
  Enable/disable Bonjour
  
  Selecting Enable allows you to use Bonjour to perform the network settings.
  
  Service name
  
  Specifies the Bonjour service name. You can use up to 48 characters for the name.
  
  Note
  - You cannot use the same service name as that already used for other LAN connected devices.
- LPR protocol setting
  
  Activates/deactivates the LPR setting.
- Wireless LAN DRX setting
  
  Selecting Enable allows you to activate discontinuous reception when using wireless LAN. It allows you to save electricity.
  
  Note
  - Depending on the access point you are using, discontinuous reception may not be activated even though Enable is selected.
  - Discontinuous reception is activated only while the machine is on standby. (The LCD is in the screen saver mode.)
- Access point mode settings
  
  When you use the machine as an access point, specify the access point name and the security setting.
  
  Using the Machine with the Access Point Mode