skip to main text

Paper-related settings

Select this setting item from Printer settings.

  • Roll paper auto feed

    Enables/disables feeding roll paper automatically when you load it on the roll unit.

    Selecting Enable detects the paper edge automatically and paper is loaded automatically only by putting roll paper on the roll unit.

    Select Disable if you load roll paper manually, or if you have any problem in feeding roll paper automatically.

    Note

    • Roll paper with a width of less than 250 mm cannot be fed automatically.

      Select Disable and feed paper manually.

  • Media type selection method

    Specifies a method to select the media type when paper is loaded.

    • Manual

      You need to select a media type from the registered media types manually.

    • Auto detect

      The media type estimated by the printer's sensor is set automatically.

      As the estimation accuracy increases, it will be not necessary to select the media type each time.

    • Auto with confirmation

      Among the media types estimated by the printer's sensor, the most likely ones are listed at the top.

      You need to select a media type from the listed media types manually.

    • Use current media type

      Select this to continue using the same type of paper.

    Note

    • When using the paper estimation function, the paper width detection function is enabled even if you set Detect paper width to Disable.

    • If the loaded paper is used by your printer for the first time, or if there is no applicable media type, No selection log entry will be displayed.

      If No selection log entry is displayed, select a media type manually.

      At this time, the printer learns the data of the selected media type.

      The next time the same paper is loaded, the media type is estimated from this data.

    • When using a paper that is not listed in the paper information list, perform Create Custom Paper in Media Configuration Tool. After create the paper information, we recommend to perform Paper feed adjustment.

    • If the created custom paper does not appear as a candidate in the paper information list even if it is fed many times, perform Paper feed adjustment again.

    • Errors may occur in the estimation results.

  • Manage remaining roll amount

    Selects the method to manage remaining roll amount and that to display warning when the roll is running short.

    • Barcodes

      Manages remaining roll amount by using a barcode.

      By using the barcode every time you replace a roll, you can manage remaining roll amount properly. Specify the roll length properly when you load a new roll.

    • Auto estimate

      Estimates and manages the remaining amount of roll paper.

      The estimated remaining roll amount is displayed on the HOME screen.

      The barcode is not printed when Auto estimate is selected.

      To estimate the remaining roll amount, Paper thickness and Paper core outer diameter have to be set correctly.

      When using a paper that is not listed in the paper information list, set Thickness and Paper Tube Size in Advanced paper settings or in Media Configuration Tool.

      For paper thickness and paper tube outer diameter size, contact the paper manufacturer.

      • Important

      • If you do not select the media type correctly, the remaining roll amount may not be estimated correctly.

      • There is an error in the estimated remaining roll amount, and paper may run out during printing.

    • Disable

      Select to disable managing remaining roll amount.

  • Roll amount warning settings

    Specifies when to warn the remaining roll paper amount.

    Note

    • This setting is enabled when Barcodes or Auto estimate is selected for Manage remaining roll amount.

  • Switch roll paper when low

    Switches the roll paper for printing automatically when the roll is running out while printing is in progress.

    • Enable

      This setting is valid only when Barcodes is selected for Manage remaining roll amount.

      The roll paper for printing is switched with several rolls remaining.

    • Disable

      Switches the roll paper for printing by estimating the remaining amount based on the roll amount value you entered.

      In addition, if the roll length is not specified properly, paper may remain when switching, or it may have run out while printing is in progress.

  • Roll paper auto switching

    Enables/Disables switching roll paper feed position by detecting the paper size.

  • Detect paper setting mismatch

    Selects printer action when you start printing with the paper size, the media type, and print settings different from those registered.

  • Paper retention settings

    Selects whether to contact the roll nip with the rolls in feeding paper.

    • If you select While feeding, the roll nip contacts with the rolls and automatic feeding is enabled.

    • If you select Release, the roll nip does not contact with the rolls.

      If you select Release, automatic feed and automatic switching of top and bottom roll paper can not be performed. Feed paper manually.

  • Advanced paper settings

    Performs advanced paper settings for each media types.

  • Paper size recognition settings

    Selects which size is preferred when paper size detection is enabled.

    • Cut sheet setting 1

      Select whether ISO A3+ or 13"x19"(Super B) is applied when a sheet of an intermediate size is detected.

    • Roll paper setting 1

      Select whether B4 or 10 in. is applied when a roll of an intermediate size is detected.

    • Roll paper setting 2

      Select whether A3 or 300 mm is applied when a roll of an intermediate size is detected.

    • Roll paper setting 3

      Select whether 300 mm or 12 in. is applied when a roll of an intermediate size is detected.

    • Roll paper setting 4

      Select whether 500 mm or 20"x24" is applied when a roll of an intermediate size is detected.

    • Roll paper setting 5

      Select whether B2 or 20"x24" is applied when a roll of an intermediate size is detected.

    • Roll paper setting 6

      Select whether A1 or 600 mm is applied when a roll of an intermediate size is detected.

    • Roll paper setting 7

      Select whether 600 mm or 24 in. is applied when a roll of an intermediate size is detected.

  • Keep margin at cut sheet end

    When printing on the sheet using AirPrint, selecting Enable sets the trailing edge of the paper to 20 mm. Select Enable if printing on the trailing edge of the paper is disturbed.

  • Print advanced paper settings

    Tapping Yes prints out each setting specified in Advanced paper settings.

  • Add priority roll paper width

    When paper size is detected, set the width of the roll paper to be recognized first. Judge in order from 1 in the list.

  • Reset all detection priority data

    Resets estimated data for all learned paper when Auto detect or Auto with confirmation is selected in Media type selection method.

  • Reset paper settings for all paper

    Tapping Yes initializes each setting specified in Advanced paper settings.

    Entering the administrator password is required if it is enabled.

    Important

    • Estimated data for all learned paper when Auto detect or Auto with confirmation is selected in Media type selection method

    • Selection log in paper type.