Menu Structure

The * on the right side of an item indicates the default value.

Values may vary depending on your model and firmware version.

• Ink information

  Current estimated ink levels

  Replace

  Order ink now

• Paper settings

  Roll paper 1
  	Replace paper
  	Feed/cut
  	Remove paper
  	Paper settings
  		Width/Length/Type/Advanced

  Roll paper 2
  	Replace paper
  	Feed/cut
  	Remove paper
  	Roll unit use setting
  	Paper settings
  		Width/Length/Type/Advanced

  Take-up mode
  	Roll unit use setting
  	Auto feed to take-up position
  	Skip errors during take-up
  		ON/OFF
  	Wind up after cutting
  		Enable/Disable
  	Paper retention setting
  		Release/Retain
  	Use in take-up mode
  		Use/Do not use

  Manual
  	Replace paper
  	Remove paper
  	Paper settings
  		Page size/Type/Advanced

• Maintenance

  Print nozzle check pattern

  Print head cleaning
  	Cleaning
  		All colors/Pattern 1/Pattern 2/Pattern 3
  	Deep cleaning
  		All colors/Pattern 1/Pattern 2/Pattern 3
  	System cleaning
  		All colors/Pattern 1/Pattern 2/Pattern 3

  Print head alignment
  	Auto (standard)
  		Roll paper 1/Roll paper 2/Manual
  	Auto (fine)
  		Roll paper 1/Roll paper 2/Manual
  	Manual
  		Roll paper 1/Roll paper 2/Manual

  Paper feed adjustment
  	Set priority
  		Roll paper 1
  			Auto*/Prioritize print quality/Prioritize length accuracy
  		Roll paper 2
  			Auto*/Prioritize print quality/Prioritize length accuracy
  		Manual
  			Auto*/Prioritize print quality/Prioritize length accuracy
  	Adjust print quality
  		Auto/Manual
  	Adjust feed length
  		Print alignment pattern
  			Roll paper 1/Roll paper 2/Manual
  		Change adjustment values

  Color calibration
  	Auto adjust
  		Roll paper 1/Roll paper 2/Manual
  	Enable/disable adjustment values
  		Enable/Disable
  	Adjustment information
  		Roll paper 1/Roll paper 2/Manual
  	Calibration guide setting
  		Enable/Disable
  	Reset adjustment values

  Maintenance cartridge info
  	Maintenance cartridge usage
  	Replace

  Head replacement

  Replace cutter blade unit

  Platen cleaning

  Prepare to transportation
  	Move indoors on the same floor
  	Move indoors to a different floor
  	Transport outdoors

• Job management

  Print job
  	List of print jobs
  		Delete/Priority printing/Release hold

  Saved job
  	Job box list
  		Job list
  			Delete/Start print
  		Print the job list

  Job history
  	Display job history
  	Print job history

  Pause printing
  	Enable
  	Disable*

• Print from USB flash drive

  Folder/file list
  	Number of copies
  	Preview
  	Settings
  	Start print

• LAN settings

  Change LAN
  	Activate wired LAN
  	Activate wireless LAN
  	Activate direct connect.
  	Disable LAN

  Wireless LAN setup
  	Cableless setup
  	Standard setup
  	WPS (Push button method)
  	Other setup
  		Advanced setup/WPS (PIN code method)

• Device settings

  Test print
  	Print nozzle check pattern
  	Status print
  	Status print (administrator)
  	Print LAN details
  	Print setting print
  	Print advanced paper settings
  	Print job history
  	Print menu map

  Print settings
  	Print head movable width setting
  		Data width*/Maximum movable width/Paper width
  	Prioritize paper size
  		Enable/Disable*
  	PDF print settings
  		Print quality settings
  			Color mode
  				Monochrome/Color*
  			Matching method
  				Perceptual (Photo)*/Saturation (Poster)
  			Print quality
  				Standard/High*/Highest
  			Input resolution
  				600 dpi*/300 dpi
  		Paper settings
  			Paper src
  				Auto select*/Roll paper (auto)/Roll paper 1/Roll paper 2/Manual
  			Margin
  				3mm*/5mm
  			Rotate
  				0 degrees*/90 degrees
  			Fit paper
  				ON*/OFF
  		Display during process
  			Warning display
  				Enable/Disable*
  	JPEG print settings
  		Print quality settings
  			Color mode
  				Monochrome/Color*
  			Matching method
  				Perceptual (Photo)*/Saturation (Poster)
  			Print quality
  				Standard/High*/Highest
  			Input resolution
  				600 dpi*/300 dpi
  		Paper settings
  			Paper src
  				Auto select*/Roll paper (auto)/Roll paper 1/Roll paper 2/Manual
  			Margin
  			3mm*/5mm
  Rotate
  	0 degrees*/90 degrees
  Fit paper
  	ON*/OFF
  Print from USB flash settings
  	Color mode
  		Monochrome/Color*
  	Print qlty
  		Standard/High*/Highest
  	Paper src
  		Auto select*/Roll paper (auto)/Roll paper 1/Roll paper 2/Manual
  	Rotate
  		0 degrees*/90 degrees
  	Fit paper
  		ON*/OFF
  Print setting print

  LAN settings
  	Change LAN
  		Activate wired LAN
  		Activate wireless LAN
  		Activate direct connect.
  		Disable LAN
  	Wireless LAN setup
  		Cableless setup
  		Standard setup
  		WPS (Push button method)
  		Other setup
  			Advanced setup/WPS (PIN code method)
  	Confirm LAN settings
  		LAN setting list
  		WLAN setting list
  		Direct connection setting list
  		Print LAN details
  	Other settings
  		Set printer name
  		TCP/IP settings
  			IPv4
  				IP address
  					Auto setup*/Manual setup
  				DNS server
  					DNS server setup
  						Auto setup/Manual setup
  					Dynamic update setting
  						Active/Inactive*
  					Host name
  					Domain name
  				Proxy server
  			IPv6
  				Enable/disable IPv6
  					Enable*/Disable
  				IPsec settings
  					Active/Inactive*
  				Use DHCPv6
  					Use/Do not use*
  				Manual address
  					Use/Do not use*
  				DNS server
  					DNS server setup
  						Auto setup/Manual setup
  					Dynamic update setting
  						IPv6 DNS dyn. update: manual
  						Active/Inactive*
  IPv6 DNS dyn. update: stateless
  	Active/Inactive*
  IPv6 DNS dyn. update: stateful
  	Active/Inactive*
  IPv6 Use IPv4 host/domain name
  	Active/Inactive*
  IPv6 DNS host name
  IPv6 DNS domain name
  WSD setting
  	Enable/disable WSD
  		Enable/Disable*
  	Optimize inbound WSD
  		Enable*/Disable
  	Timeout setting
  		20 minutes/15 minutes*/10 minutes/5 minutes/1 minute
  Bonjour settings
  	Enable/disable Bonjour
  		Enable*/Disable
  	Service name
  IEEE802.1X settings
  	Authentication
  		Do not use*/TLS/TTLS/PEAP
  	EAP-TTLS internal auth. method
  		MSCHAPv2*/PAP
  	Weak encryption restriction
  		Restrict*/Do not restrict
  	Weak certificate restriction
  		Restrict*/Do not restrict
  	Advanced setup
  		User-ID/Username/Password/Authentication server name
  	Last authentication result
  SNTP settings
  	Client operation status
  		Active/Inactive*
  	NTP/SNTP server address
  	Polling interval
  Spanning tree setting
  	Active/Inactive*
  LPR protocol setting
  	Enable*/Disable
  RAW protocol
  	ON*/OFF
  LLMNR
  	ON*/OFF
  Wireless LAN DRX setting
  	Enable*/Disable
  Wired LAN DRX setting
  	Enable*/Disable
  Direct connection settings
  	Update SSID/password
  	Direct connection device name
  	Connection request confirmation
  		Yes*/No
  Reset SSL certificates
  Reset LAN settings

  Paper-related settings
  	Manage remaining roll amount
  		Enable/Disable*
  	Roll paper auto switching
  		Identify size*/Do not identify size
  	Keep media type
  		Enable/Disable*
  	Detect paper setting mismatch
  		Pause/Display warning*/Do not detect/Hold job
  	Paper retention setting
  		Release/Retain*
  	Energy save mode paper rewind
  		Enable/Disable*
  	Advanced paper settings
  	Paper size recognition settings
  		Cut sheet setting 1/Cut sheet setting 2/Roll paper setting 1/Roll paper setting 2
  	Adjust roll unit
  	Print advanced paper settings
  	Reset paper settings for all paper

  Auto maintenance settings
  	Auto nozzle check
  		Standard*/1 page/10 pages/Disable
  	Nozzle check error display
  		Enable/Disable*
  	System cleaning frequency
  		Standard*/Short
  	Print pattern after new head
  		ON*/OFF

  Hard disk settings
  	Output method
  		Print*/Print (auto delete)/Save to job box
  	Save first and print
  		ON/OFF*
  	Common job box setting
  		Print*/Print (auto delete)
  	Data deletion
  		Fast/Fast secure/Secure

  Monitoring service settings
  	Enable/disable monitoring service
  		Enable/Disable*
  	Communication test
  		Yes/No
  	Communication log

  Device user settings
  	Energy saving settings
  		Auto power off
  			5 minutes/10 min./30 min./1 hour/4 hours/8 hours*/12 hours/OFF
  		Sleep timer
  			5 minutes*/10 min./15 min./20 min./30 min./40 min./50 min./60 min.
  	Operation restrictions
  		Job history
  			Restrict/Do not restrict*
  		Remote UI
  			Restrict/Do not restrict*
  		Print from USB flash drive
  			Restrict/Do not restrict*
  	Use USB connection
  		Use*/Do not use
  	Date/time setting
  	Date display format
  		YYYY/MM/DD / MM/DD/YYYY / DD/MM/YYYY
  	Time zone (GMT)
  		0/+1/+2/+3/+4/+5/+6/+7/+8/+9/+10/+11/+12/-12/-11/-10/-9/-8/-7/-6/-5/-4/-3/-2/-1
  	Length unit setting
  		Meters*/Feet/inches
  	Buzzer setting
  		Enable*/Disable
  	EOP timer setting
  		10 seconds/30 seconds/1 minute/2 minutes/5 minutes/10 minutes*/30 minutes/60 minutes
  	Job history sending setting
  		Send/Do not send*

  Language selection

  Firmware update
  	Install update
  	Check current version
  	Update notification setting
  		Yes*/No
  	DNS server setup
  		Auto setup*/Manual setup
  	Proxy server setup
  		Use/Do not use*

  Administrator password setting
  	Remote UI or other tools/LCD, Remote UI, or other tools

• Printer information

  System information

  Hard disk information

  Error history
  	Hardware error
  	Recoverable error

  Records of use

  Head information

  Head alignment performance log

  Values applied with auto settings