LAN settings

Select this setting item from HOME screen.

Important

• The administrator password is required to change settings if it is enabled for changing settings using the operation panel.

• Wi-Fi

  The following setting information on the Wi-Fi connection is displayed. (Some items are not displayed depending on printer settings.)

  Items	Setting
  Connection	Enabled (connected) / Enabled (disconnected) / Disable
  Network name (SSID)	XXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXX (up to 32 characters)
  Communication mode	Infrastructure
  Channel	XX (up to 2 digits)
  Wi-Fi security	Disable / WEP (64 bit) / WEP (128 bit) / WPA-PSK (TKIP) / WPA-PSK (AES) / WPA2-PSK (TKIP) / WPA2-PSK (AES)
  IPv4 address	XXX. XXX. XXX. XXX (12 characters)
  IPv4 subnet mask	XXX. XXX. XXX. XXX (12 characters)
  IPv4 default gateway	XXX. XXX. XXX. XXX (12 characters)
  IPv4 DNS dynamic setting	Active / Inactive
  IPv4 DNS host name	XXXXXXXXXXXX
  IPv4 DNS domain name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXX (up to 64 characters)
  IPv6 link-local address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 link-local prefix length	XXX (up to 3 digits)
  IPv6 manual address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 manual prefix length	XXX (up to 3 digits)
  IPv6 stateless address 1	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 1	XXX (up to 3 digits)
  IPv6 stateless address 2	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 2	XXX (up to 3 digits)
  IPv6 stateless address 3	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 3	XXX (up to 3 digits)
  IPv6 stateless address 4	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 4	XXX (up to 3 digits)
  DHCPv6	Active / Inactive
  DHCPv6 stateful address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  DHCPv6 stateful prefix length	XXX (up to 3 digits)
  IPv6 default gateway 1	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 2	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 3	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 4	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 primary DNS server address	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 39 characters)
  IPv6 secondary DNS server add.	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 39 characters)
  IPv6 DNS dyn. update: manual	Active / Inactive
  IPv6 DNS dyn. update: stateless	Active / Inactive
  IPv6 DNS dyn. update: stateful	Active / Inactive
  IPv6 Use IPv4 host/domain name	Active / Inactive
  IPv6 DNS host name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXX (up to 63 characters)
  IPv6 DNS domain name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXX (up to 64 characters)
  MAC address	XX:XX:XX:XX:XX:XX (12 characters)
  IPsec settings	Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable
  Printer name	XXXXXXXXXXXXXXX (up to 15 characters)
  Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters)

  ("XX" represents alphanumeric characters.)

  To change the setting, tap Settings.

  • Enable/disable Wi-Fi

    Select Enable to wirelessly connect via wireless router.

  • Wi-Fi setup

    Select how to setup Wi-Fi.

    • Easy wireless connect

      Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure.

    • Manual connect

      Select when you perform settings for Wi-Fi manually using the operation panel of the printer.

    • WPS (Push button method)

      Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.

    • Other connection types

      • Advanced setup

        Select when you perform settings for Wi-Fi manually. You can specify multiple WEP keys.

      • WPS (PIN code method)

        Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.

  Note

  • By tapping Advanced, you can set LAN in detail.

    For the items that can be set, see the following.

    • Advanced

• Wireless Direct

  The following setting information on the Wireless Direct connection is displayed. (Some items are not displayed depending on printer settings.)

  Items	Setting
  Connection	Enabled (connected) / Enabled (disconnected)
  Network (SSID)/device name	DIRECT-XXXX-PRO-4100S
  Password	XXXXXXXXXX (10 characters)
  Communication mode	Wireless Direct
  Channel	3
  Wi-Fi security	WPA2-PSK (AES)
  IPv4 address	XXX. XXX. XXX. XXX (12 characters)
  IPv4 subnet mask	XXX. XXX. XXX. XXX (12 characters)
  IPv4 default gateway	XXX. XXX. XXX. XXX (12 characters)
  IPv4 DNS dynamic setting	Active / Inactive
  IPv4 DNS host name	XXXXXXXXXXXX
  IPv4 DNS domain name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXX (up to 64 characters)
  IPv6 link-local address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 link-local prefix length	XXX (up to 3 digits)
  MAC address	XX:XX:XX:XX:XX:XX (12 characters)
  IPsec settings	Inactive
  Printer name	XXXXXXXXXXXXXXX (up to 15 characters)
  Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters)

  ("XX" represents alphanumeric characters.)

  To change the setting, tap Settings.

  • Enable/disable Wireless Direct

    Select Yes to wirelessly connect without wireless router.

  • Update SSID/password

    Updates the identifier (SSID) and password.

  • Wireless Direct device name

    Changes the name (device name) of the printer displayed on Wi-Fi Direct compatible device.

  • Connection request confirmation

    Changes the display / non-display of the confirmation screen when Wi-Fi Direct compatible devices are connected to the printer.

  Note

  • By tapping Advanced, you can set LAN in detail.

    For the items that can be set, see the following.

    • Advanced

• Wired LAN

  The following setting information on the Wired LAN connection is displayed. (Some items are not displayed depending on printer settings.)

  Items	Setting
  Connection	Enabled (connected) / Enabled (disconnected) / Disable
  IPv4 address	XXX. XXX. XXX. XXX (12 characters)
  IPv4 subnet mask	XXX. XXX. XXX. XXX (12 characters)
  IPv4 default gateway	XXX. XXX. XXX. XXX (12 characters)
  IPv4 DNS dynamic setting	Active / Inactive
  IPv4 DNS host name	XXXXXXXXXXXX
  IPv4 DNS domain name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXX (up to 64 characters)
  IPv6 link-local address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 link-local prefix length	XXX (up to 3 digits)
  IPv6 manual address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 manual prefix length	XXX (up to 3 digits)
  IPv6 stateless address 1	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 1	XXX (up to 3 digits)
  IPv6 stateless address 2	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 2	XXX (up to 3 digits)
  IPv6 stateless address 3	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 3	XXX (up to 3 digits)
  IPv6 stateless address 4	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 stateless prefix length 4	XXX (up to 3 digits)
  DHCPv6	Active / Inactive
  DHCPv6 stateful address	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  DHCPv6 stateful prefix length	XXX (up to 3 digits)
  IPv6 default gateway 1	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 2	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 3	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 default gateway 4	XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX (32 characters)
  IPv6 primary DNS server address	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 39 characters)
  IPv6 secondary DNS server add.	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 39 characters)
  IPv6 DNS dyn. update: manual	Active / Inactive
  IPv6 DNS dyn. update: stateless	Active / Inactive
  IPv6 DNS dyn. update: stateful	Active / Inactive
  IPv6 Use IPv4 host/domain name	Active / Inactive
  IPv6 DNS host name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXX (up to 63 characters)
  IPv6 DNS domain name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXX (up to 64 characters)
  MAC address	XX:XX:XX:XX:XX:XX (12 characters)
  IPsec settings	Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable
  Printer name	XXXXXXXXXXXXXXX (up to 15 characters)
  Bonjour service name	XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX (up to 52 characters)

  ("XX" represents alphanumeric characters.)

  To change the setting, tap Settings.

  • Enable/disable Wired LAN

    Select Enable when connecting to wired LAN.

  Note

  • By tapping Advanced, you can set LAN in detail.

    For the items that can be set, see the following.

    • Advanced

• Print details

  Prints out the LAN setting information of the printer with Wi-Fi connection, wired LAN connection, wireless direct connection.

  For the items that can be checked, see the following.

  • Printing Network Settings

  Important

  • Important information on your computer is stated on the paper on which the LAN setting information is printed. Please handle with care enough.

  Note

  • You can also print out the LAN setting information by tapping in the following order.

    Device settings > Test print > Print LAN details

• Advanced

  By tapping Advanced on each setting screen of Wi-Fi connection, wired LAN connection, wireless direct connection, LAN information can be set in detail.

  Important

  • If the LAN is disabled, the following items can not be selected.

  • Set printer name

    Specifies the printer name. You can use 2 to 15 characters for the name.

    Note

    • You cannot use the same printer name as that already used for other LAN connected devices.
    • You cannot use a hyphen for the initial or last character of the printer name.

  • TCP/IP settings

    Performs IPv4 or IPv6 setting.

  • WSD setting

    Setting items when you use WSD (one of the network protocols supported in Windows 10, Windows 8.1, and Windows 7).

    • Enable/disable WSD

      Selects whether WSD is enabled or disabled.

      Note

      • When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows 10, Windows 8.1, and Windows 7.

    • Optimize inbound WSD

      Selecting Enable allows you to receive the WSD printing data faster.

    • Timeout setting

      Specifies the timeout length.

  • Bonjour settings

    Setting items when you use Bonjour.

    • Enable/disable Bonjour

      Selecting Enable allows you to use Bonjour to perform the network settings.

    • Service name

      Specifies the Bonjour service name. You can use up to 48 characters for the name.

      Note

      • You cannot use the same service name as that already used for other LAN connected devices.

  • IEEE802.1X settings

    Performs various settings for IEEE802.1X.

  • SNTP settings

    Performs various settings for SNTP (Simple Network Time Protocol).

  • Spanning tree setting

    Enables/Disables spanning tree. Selecting Active avoids circulating data on a network.

  • LPR protocol setting

    Enables/Disables the LPR setting.

  • RAW protocol

    Enables/Disables RAW printing.

  • LLMNR

    Specifies ON/OFF of LLMNR (Link-Local Multicast Name Resolution). Selecting ON allows the printer to detect printer's IP address from the printer name without a DNS server.

  • Gigabit Ethernet settings

    Specifies the communication speed and communication method when using Gigabit Ethernet.

  • Use Dedicated Port

    Selects whether to use a dedicated port for a command sent from a Canon application to the printer.

    Selecting ON allows you to use the dedicated port.

  • IPP settings

    Selecting Enable allows you to print via the network with the IPP protocol.

    If you use the security print function when printing using IPP protocol in AirPrint etc., select Enable for Security Print.

  • Wi-Fi DRX setting

    Selecting Enable allows you to activate discontinuous reception when using Wi-Fi.

  • Wired LAN DRX setting

    Selecting Enable allows you to activate discontinuous reception when the printer is connected to a device compatible with wired LAN.

  • Reset SSL certificates

    Initializes SSL certificate information.

  • Reset LAN settings

    Initializes the network settings on the printer.

    After resetting, perform setup again as necessary.