LAN settings
Select this setting item from HOME screen.
Important
- The administrator password is required to change settings if it is enabled for changing settings using the operation panel.
-
Wi-Fi
The following setting information on the Wi-Fi connection is displayed. (Some items are not displayed depending on printer settings.)
Items Setting Connection Enabled (connected) / Enabled (disconnected) / Disable Network name (SSID) XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX (up to 32 characters)Communication mode Infrastructure Frequency 2.4GHz / 5GHz Channel XX (up to 2 digits) Wi-Fi security Disable / WEP (64 bit) / WEP (128 bit) / WPA-PSK (TKIP) / WPA-PSK (AES) / WPA2-PSK (TKIP) / WPA2-PSK (AES) Signal strength (%) XXX IPv4 address XXX. XXX. XXX. XXX (12 characters) IPv4 subnet mask XXX. XXX. XXX. XXX (12 characters) IPv4 default gateway XXX. XXX. XXX. XXX (12 characters) IPv6 link-local address XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 link-local prefix length XXX (up to 3 digits) IPv6 manual address XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 manual prefix length XXX (up to 3 digits) IPv6 stateless address 1 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 1 XXX (up to 3 digits) IPv6 stateless address 2 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 2 XXX (up to 3 digits) IPv6 stateless address 3 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 3 XXX (up to 3 digits) IPv6 stateless address 4 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 4 XXX (up to 3 digits) IPv6 default gateway 1 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 2 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 3 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 4 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)MAC address (Wi-Fi) XX:XX:XX:XX:XX:XX (12 characters) IPsec settings Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable Printer name XXXXXXXXXXXXXXX (up to 15 characters) Bonjour service name XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX (up to 52 characters)("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wi-Fi
Select Enable to wirelessly connect via wireless router.
-
Wi-Fi setup
Select how to setup Wi-Fi.
-
Easy wireless connect
Select if you specify the settings of the access point information to the printer directly from a device (e.g. smartphone, or tablet) without operating the wireless router. Follow the on-screen instructions of the connecting device for the setup procedure.
-
Manual connect
Select when you perform settings for Wi-Fi manually using the operation panel of the printer.
-
WPS (Push button method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) push button method. Follow the on-screen instructions during setup.
-
Other connection types
-
Manual connect (adv.)
Select when you perform settings for Wi-Fi manually. You can specify multiple WEP keys.
-
WPS (PIN code method)
Select when you perform settings for Wi-Fi using a wireless router supporting a Wi-Fi Protected Setup (WPS) PIN code method. Follow the on-screen instructions during setup.
-
-
-
Advanced
For details on each setting item:
-
-
Wireless Direct
The following setting information on the Wireless Direct connection is displayed. (Some items are not displayed depending on printer settings.)
Items Setting Connection Enable / Disable Network (SSID)/device name DIRECT-XXXX-PRO-200series Password XXXXXXXXXX (10 characters) Communication mode Wireless Direct Channel 3 Wi-Fi security WPA2-PSK (AES) No. of printers connected now XX / XX IPv4 address XXX. XXX. XXX. XXX (12 characters) IPv4 subnet mask XXX. XXX. XXX. XXX (12 characters) IPv4 default gateway XXX. XXX. XXX. XXX (12 characters) IPv6 link-local address XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 link-local prefix length XXX (up to 3 digits) MAC address (Wi-Fi) XX:XX:XX:XX:XX:XX (12 characters) IPsec settings Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable Printer name XXXXXXXXXXXXXXX (up to 15 characters) Bonjour service name XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX (up to 52 characters)("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wireless Direct
Select Yes to wirelessly connect without wireless router.
-
Change SSID/device name
Changes the identifier (SSID/the printer's name displayed on a Wi-Fi Direct compatible device) for Wireless Direct.
-
Change password
Changes the password for Wireless Direct.
-
Connection request confirmation
Changes the display/non-display of the confirmation screen when Wi-Fi Direct compatible devices are connected to the printer.
-
Advanced
For details on each setting item:
-
-
Wired LAN
The following setting information on the Wired LAN connection is displayed. (Some items are not displayed depending on printer settings.)
Items Setting Connection Enabled (connected) / Enabled (disconnected) / Disable IPv4 address XXX. XXX. XXX. XXX (12 characters) IPv4 subnet mask XXX. XXX. XXX. XXX (12 characters) IPv4 default gateway XXX. XXX. XXX. XXX (12 characters) IPv6 link-local address XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 link-local prefix length XXX (up to 3 digits) IPv6 manual address XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 manual prefix length XXX (up to 3 digits) IPv6 stateless address 1 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 1 XXX (up to 3 digits) IPv6 stateless address 2 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 2 XXX (up to 3 digits) IPv6 stateless address 3 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 3 XXX (up to 3 digits) IPv6 stateless address 4 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 stateless prefix length 4 XXX (up to 3 digits) IPv6 default gateway 1 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 2 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 3 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)IPv6 default gateway 4 XXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXX (32 characters)MAC address (Wired LAN) XX:XX:XX:XX:XX:XX (12 characters) IPsec settings Enable (ESP) / Enable (ESP & AH) / Enable (AH) / Disable Printer name XXXXXXXXXXXXXXX (up to 15 characters) Bonjour service name XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX (up to 52 characters)("XX" represents alphanumeric characters.)
To change the setting, select Settings.
-
Enable/disable Wired LAN
Select Enable when connecting to wired LAN.
-
Advanced
For details on each setting item:
-
-
Print details
Prints out the LAN setting information of the printer with Wi-Fi connection, wired LAN connection, wireless direct connection.
For the items that can be checked, see the following.
Important
- Important information on your computer is stated on the paper on which the LAN setting information is printed. Please handle with care enough.
Note
-
You can also print out the LAN setting information by selecting in the following order from the HOME screen.
LAN settings > Print details
-
Advanced
By selecting Advanced on each setting screen of Wi-Fi connection, wired LAN connection, wireless direct connection, LAN information can be set in detail.
Important
- If the LAN is disabled, the following items can not be selected.
-
Set printer name
Specifies the printer name. You can use 2 to 15 characters for the name.
Note
- You cannot use the same printer name as that already used for other LAN connected devices.
- You cannot use a hyphen for the initial or last character of the printer name.
-
TCP/IP settings
Performs IPv4 or IPv6 setting.
-
WSD settings
Setting items when you use WSD (one of the network protocols supported in Windows 10, Windows 8.1, and Windows 7).
-
Enable/disable WSD
Selects whether WSD is enabled or disabled.
Note
- When this setting is enabled, the printer icon is displayed on the Network Explorer in Windows 10, Windows 8.1, and Windows 7.
-
Optimize inbound WSD
Selecting Enable allows you to receive the WSD printing data faster.
-
Timeout settings
Specifies the timeout length.
-
-
Bonjour settings
Setting items when you use Bonjour.
-
Enable/disable Bonjour
Selecting Enable allows you to use Bonjour to perform the network settings.
-
Service name
Specifies the Bonjour service name. You can use up to 48 characters for the name.
Note
- You cannot use the same service name as that already used for other LAN connected devices.
-
-
IEEE802.1X settings
Sets the IEEE802.1X authentication method, etc.
-
LPR protocol settings
Enables/Disables the LPR setting.
-
RAW protocol
Enables/Disables RAW printing.
-
LLMNR
Specifies ON/OFF of LLMNR (Link-Local Multicast Name Resolution). Selecting ON allows the printer to detect printer's IP address from the printer name without a DNS server.
-
IPP settings
Selecting Enable allows you to print via the network with the IPP protocol.
-
PictBridge communication
Setting items for printing from a PictBridge (Wi-Fi) compliant device.
-
Enable/disable communication
Selecting Enable allows you to print from a PictBridge (Wi-Fi) compliant device.
-
Timeout setting
Specifies the timeout length.
-
-
Wi-Fi DRX settings
Selecting Enable allows you to activate discontinuous reception when using Wi-Fi.
-
Wired LAN DRX settings
Selecting Enable allows you to activate discontinuous reception when the printer is connected to a device compatible with wired LAN.
-
IPsec settings
Selecting Enable allows you to specify the IPsec security.